|
|
Gulf Synthetics, ConcreteRevive
| Colors: | |  |
Do-it-yourself durable concrete coating
ConcreteRevive (UCF-30) is a non-toxic, water-based coating that crosslinks with exterior paint to form a hard, durable, protective covering that protects any concrete substrate. It also helps prevent bleed through from nails and fasteners. Mix ConcreteRevive with colored paint to transform old, worn out, beat-up concrete masonry, stucco or anything made of cement.
Unlike most exterior coatings that are solvent-based and highly toxic, ConcreteRevive is non-toxic, zero VOC and has absolutely no odor once dried.
Why we like it
If you believe in miracles, this might be considered a true concrete-saver. It transforms old concrete, masonry, stucco or brick into a beautiful, skid-resistant surface that'll last a very long time. We espeically like it because you rarely have to recoat or touch up. NOTE: Color-matching may require several test runs to produce the correct color.
Features & benefits
- Easy-to-use — mix and paint as usual
- Fast-drying — dry to touch in minutes; open to foot traffic in a few hours
- Multi-purpose — use on walkways, pool decks, driveways, garages, basements, concrete walls, stucco and brick
- Long-lasting — stain, scuff, skid and fire-resistant
- Rust inhibitor — helps prevent bleed through from nails and fasteners
- Unlimited color range — add to any color latex or acrylic paint
- Non-toxic — contains no hazardous chemicals; will not off-gas toxic fumes
- Safe — for everyone, including the chemically sensitive. learn how to test a non-toxic product for tolerance
- Eco-friendly — zero VOC
Alert: Specs
| Basics |
|---|
| Interior or Exterior | Exterior, Interior |
| Use On Material | concrete - pre-cast, stone - unsealed, stone - porous, masonry - porous, block, brick, clay or concrete roof tiles, concrete, stone, stucco, tile - unglazed, surfaces - porous, concrete - painted, concrete - sealed, concrete - unsealed, masonry - sealed, masonry - unsealed, dry wells, masonry |
| Use On | Clean tools with water. keep a lid on any extra product and store in a cool, dark and dry space. activated coatings will have an approximate 14-day pot life. buckets should be cleaned and re-use then |
| Location | commercial buildings, deck & patio, driveway, entryway, garage, hot tub (sauna, whirlpool, bath tub), laundry room, outhouse, basement, bathroom - wet, boats, cabins |
| Eco-replacement for | |
| Chemically-sensitive safe | Yes learn how to test a non-toxic product for tolerance |
| Test before use | Yes, test on inconspicuous area |
| Dimensions |
|---|
| Coverage | 1-Kit = 200 SF (2 coats) |
| Square Feet / Box | Square Feet |
| Boxes / Pallet | Boxes |
| Square Feet / Pallet | Square Feet |
| Boards / Box | Boards |
| Pieces / Box | Pieces |
| Weight / Box | Pounds |
| Thickness or Height | " |
| Thickness | mm |
| Veneer Cut Thickness | |
| Length | " |
| Length | mm |
| Width | " |
| Width | mm |
| Features |
|---|
| Minimum Order | |
| Old Name | |
| Origin | |
| Recycled Content | |
| Shelf Life | |
| Use With These Prodcuts | |
| Number of Colors | Colors |
| Carpet Pattern | |
| Coordinating Border | |
| Critical Radiant Flux | |
| Extractable Matter | |
| Face or Pile Weight | |
| Fiber | |
| General Flammability | |
| Surface Flammability | |
| GSA Classification | |
| Line | |
| Machine Guage | |
| Moth Resistance | |
| Pattern Repeat | |
| Pile Height (High) | |
| Pile Height (Low) | |
| Primary Backing | |
| Resistance to Insect Pests | |
| Roll Length | ' |
| Secondary Backing | |
| Smoke Density | |
| Static | |
| Stitches Per Inch | |
| Surface Texture, Construction, Style | |
| Total Height | |
| Total Weight | |
| Traffic Rating | |
| Tufts per Sq. In. | Tufts / Sq In |
| Yarn Construction | |
| Bundles per Pallet | Bundles |
| Bundles per Square 6" Exposure | Bundles |
| Bundles per Square 7" Exposure | Bundles |
| Bundles per Square 7-1/2" Exposure | Bundles |
| Bundles per Square 8" Exposure | Bundles |
| Pounds per Bundle | Pounds |
| Pounds per Pallet | Pounds |
| Pounds per Roll | Pounds |
| Pounds per Square | Pounds |
| Pounds per Square 6" Exposure | Pounds |
| Pounds per Square 7" Exposure | Pounds |
| Pounds per Square 7-1/2" Exposure | Pounds |
| Pounds per Square 8" Exposure | Pounds |
| Lin Feet per Bundle | Lin Feet |
| Lin Feet per Pallet | Lin Feet |
| Rolls per Pallet | Rolls |
| Squares per Roll | Squares |
| Tiles per bundle | Tiles |
| Tiles per Lin Foot | Tiles |
| Finish Type | |
| Base | Water-based |
| Ingredients | download Material Safety Data Sheet (MSDS) |
| VOC Content | Zero VOC Grams/Liter |
| Use On Material - Condition | concrete - pre-cast, stone - unsealed, stone - porous, masonry - porous, block, brick, clay or concrete roof tiles, concrete, stone, stucco, tile - unglazed, surfaces - porous, concrete - painted, concrete - sealed, concrete - unsealed, masonry - sealed, masonry - unsealed, dry wells, masonry |
| Use On Instructions | Clean tools with water. keep a lid on any extra product and store in a cool, dark and dry space. activated coatings will have an approximate 14-day pot life. buckets should be cleaned and re-use then |
| Application Method | brush, roller |
| Application Temperature Range | between 50-85 ° f |
| Application Instructions | Each kit of UCF-30 is packaged in a five-gallon container for easy mixing. The kit contains two parts: (1) liquid resin and (2) dry chemistry. YOU ADD two quarts of exterior latex or acrylic paint (any color of flat, eggshell or semi-gloss). With two coats applied, the coverage will be approximately 200 square feet.
Application Procedure for One Kit:
Remove both wet and dry chemistry from container.
Empty white liquid resin into container.
Add two quarts of exterior latex or acrylic paint (any color)-resin. Mix briskly for one minute.
Slowly add dry chemistry while stirring briskly with drill mixer for five minutes. Stir mixture-loosen up any dry portion from the bottom of container. Dry chemistry components should break down completely and mix should be smooth and viscous. The coating is now activated and should be used immediately.
5. Do not alter the chemistry of the product in any way by adding or subtracting material or by adding other ingredients (DO NOT ADD WATER).
If you are working on a large area with more than one kit, mix each kit separately and then blend or _Boxî together for color consistency.
Use typical _cut inî techniques around adjacent structures, etc. Cut in with two coats. Allow-dry between coats.
Allow UCF-30-dry-the touch, usually about 1 hour under normal temperature and humidity. However, if it is very cool or very humid it could take longer and conversely; if it is warmer and dryer, it could take less time-dry.
For best coverage, use a 3/8î nap paint roller and apply the first coat in a north-south direction. Allow-dry completely before applying the second coat.
10. Apply second coat in an east-west direction. The second coat is key-attaining the proper texture. If a more aggressive non-slip texture is desired, use a one-inch nap roller for second coat. Be consistent in your technique. Allow-dry.
11. Additional coats may be applied-build the final mil thickness, if desired.
12. After UCF-30 is applied and thoroughly dried, it is recommended, but not required,-apply two coats of a non-yellowing acrylic sealer for decorative concrete, such as AFM Mexeseal. This will make cleanup easier in areas where food, dirt and grease collect easily. Follow sealer manufacturers recommendations for best use. |
| Surface or Product Preperation | Surface should be clean, dry, dull, pH neautral, and of moderate temperature
CLEAN: Surfaces should be thoroughly clean, free of dirt, sealer or waxes, peeling paint, mildew, tar, glaze, efflorescence, laitance, grease or oily substances. Loose mortar or cement should be removed. Clean the surface by power washing, and allow substrate to dry completely for a minimum of 48 hours
DRY: The surface needs to be thoroughly dry. Never apply over wet concrete. For exterior projects do not apply if rain is predicted in the next 30 hours. Test concrete for possible moisture problems by taping an 18î X 18î plastic film to the concrete and observing it for 24 hours. If condensation is observed, moisture is present and the source should be identified and contained before proceeding
DULL: Glossy, painted, or sealed surfaces should be dulled by grinding or acid etching. If a clear concrete sealer is on the surface that is to be coated, the surface should be acid etched using a 10 percent muriatic acid solution or grinded to produce a profile for the UCF-30 coating to bond to. Then the surface is to be cleaned thoroughly by power washing. Note: Wear work goggles, rubber gloves and boots and protective clothing when using muriatic acid. A less toxic option is GBS Microetch
PH NEUTRAL: New concrete has a very high PH. Allow new concrete to cure 30-60 days at 75 degrees before coating. Concrete should have a PH of 7-9 before applying this product. Test with litmus paper
MODERATE TEMPERATURE: Ideal temperature for application should be 50-85 degrees F. Do not apply if ambient temperature or the surface temperature is <50 degrees or >85 degrees F. If temperature is less than 50 degrees F this product will cure too slowly or maybe not at all. If temperatures exceed 85 degrees F, this coating will set too quickly
PREPPING HOLES AND CRACKS: UCF-30 is quite thick and will easily fill most small cracks. If existing cracks are excessive (over 3/8î deep and wide), use an acrylic concrete caulk or commonly available concrete patching material to infill these areas before coating with UCF-30. Do not smear caulk/patching material on adjacent concrete surface. Caulk or patching material should be properly dried or cured before applying UCF-30. See manufacturers instructions for the proper application of these materials |
| Recommended # of Coats | 2 |
| Re-coat After | as needed |
| Drying Time | 1-2 hours |
| Appearance When Dry | depends on type and color of paint |
| Cleans Up With | Water |
| Storage | Store in cool dry place out of sunlight |
| Recycling or Disposal | dispose of excess product in accordance with all local, state and federal regulations., do not through out containers unless completely empty. spread out contents onto dry cardboard or newspaper and thoroughly dry outdoors. you may also absorb with cat litter, sand or other dry material |
| Adhesive | |
| Bamboo Construction | |
| Bathroom Installation | |
| Color Change | |
| Construction | |
| Construction Description | |
| Durability | |
| Edge | |
| Finish | |
| Finish Sheen | |
| Floor Item Type | |
| Floor Pattern | |
| Floor Type | |
| Grade Installation | |
| Grading | |
| Installation | |
| Janka Hardness Rating | |
| Joint System | |
| Knots | |
| Material | |
| Number of Plys | -Plys |
| Composition | |
| Radiant Heat | |
| Range of Resistance | |
| Risk in Dry Climates | |
| Style | |
| Shade (1 Light) - (7 Dark) | |
| Strips / Plank | -Strips/Plank |
| Surface Texture | |
| Surface Treatment | |
| Surface Treatment Color | |
| Tile Application | |
| Touch Up Kit | |
| Can be indoor? | |
| Can be outdoor? | |
| Direct Vent? | |
| Easy-Linkable? | |
| Energy Factor | |
| Max Gallons Per Minute | - GPM |
| Max BTU's / Hour | - BTU's / Hour |
| Multi Control Capabilities | |
| Temperature Range (with remote) | |
| Warranty |
|---|
| Warranties | |
| Residential Finish Wear | |
| Residential Structural | |
| Commercial Finish Wear | |
| Commercial Structural | |
| Certifications |
|---|
| Forest Stewardship Council (FSC) | |
| FSC Content | |
| FSC Chain-of-Custody # | |
| LEED® Qualifications | |
| LEED® Regional Materials Zip Code | |
| Certifications | |
Accessories
Gulf Synthetics, ConcreteRevive
| | Items | Options | Price |
|
DIY, non-toxic, durable, non-skid protective coating for concrete and masonry surfaces |
|
|
|
|
|
Gulf Synthetics, ConcreteRevive
Item #14808
Was | |
Discount | |
Lifetime Phone Support | FREE |
Shipping | FREE* | |
|
|
|
|
Calculate
Shipping
